Settings for registers of I2C Extend Click driver. More...

Macros
#define	I2CEXTEND_CONFIG_INTR_MODE_BIT_MASK 0x01
	I2C Extend description setting.

#define	I2CEXTEND_CONFIG_INTR_MODE_SET_ALERT_PIN 0x00

#define	I2CEXTEND_CONFIG_INTR_MODE_IGNORE_ARA 0x01

#define	I2CEXTEND_CONFIG_CTRL_SEL_BIT_MASK 0x02

#define	I2CEXTEND_CONFIG_CTRL_SEL_MIRRORED_RMT_OUT 0x00

#define	I2CEXTEND_CONFIG_CTRL_SEL_USE_REG_CTRL_VAL 0x02

#define	I2CEXTEND_ALERT_EN_LINK_GOOD_DISABLE 0x00
	I2C Extend alert enable.

#define	I2CEXTEND_ALERT_EN_LINK_GOOD 0x01

#define	I2CEXTEND_ALERT_EN_LINK_LOST_DISABLE 0x00

#define	I2CEXTEND_ALERT_EN_LINK_LOST 0x02

#define	I2CEXTEND_ALERT_EN_FAULT_DISABLE 0x00

#define	I2CEXTEND_ALERT_EN_FAULT 0x04

#define	I2CEXTEND_CTRL_SEL_L 0x00
	I2C Extend control.

#define	I2CEXTEND_CTRL_SEL_H 0x01

#define	I2CEXTEND_PIN_STATE_LOW 0x00
	I2C Extend pin state.

#define	I2CEXTEND_PIN_STATE_HIGH 0x01

#define	C6DOFIMU11_CNTL2_TEMP_EN_STANDBY_MODE 0x00
	6DOF IMU 11 bit mask.

#define	C6DOFIMU11_CNTL2_MAG_EN_STANDBY_MODE 0x00

#define	C6DOFIMU11_CNTL2_ACCEL_EN_STANDBY_MODE 0x00

#define	C6DOFIMU11_INC3_IEL2_FIFO_TRIG 0x20

#define	C6DOFIMU11_INC3_IEL1_FIFO_TRIG 0x02

#define	C6DOFIMU11_CNTL2_ACCEL_EN_OPERATING_MODE 0x01

#define	C6DOFIMU11_CNTL2_GSEL_8G 0x00

#define	C6DOFIMU11_CNTL2_RES_MAX2 0x0C

#define	C6DOFIMU11_CNTL2_MAG_EN_OPERATING_MODE 0x02

#define	C6DOFIMU11_WHO_AM_I_WIA_ID 0x2D

#define	I2CEXTEND_I2C_SLAVE_ADDR_0 0x3E
	I2C Extend device address setting.

#define	I2CEXTEND_I2C_SLAVE_ADDR_1 0x3F

#define	I2CEXTEND_I2C_SLAVE_ADDR_2 0x76

#define	I2CEXTEND_I2C_SLAVE_ADDR_3 0x77

#define	C6DOFIMU11_I2C_SLAVE_ADDRESS_GND 0x0E
	6DOF IMU 11 device address setting.

#define	C6DOFIMU11_I2C_SLAVE_ADDRESS_VCC 0x0F

Detailed Description

Settings for registers of I2C Extend Click driver.

Macro Definition Documentation

◆ C6DOFIMU11_CNTL2_ACCEL_EN_OPERATING_MODE

#define C6DOFIMU11_CNTL2_ACCEL_EN_OPERATING_MODE 0x01

◆ C6DOFIMU11_CNTL2_ACCEL_EN_STANDBY_MODE

#define C6DOFIMU11_CNTL2_ACCEL_EN_STANDBY_MODE 0x00

◆ C6DOFIMU11_CNTL2_GSEL_8G

#define C6DOFIMU11_CNTL2_GSEL_8G 0x00

◆ C6DOFIMU11_CNTL2_MAG_EN_OPERATING_MODE

#define C6DOFIMU11_CNTL2_MAG_EN_OPERATING_MODE 0x02

◆ C6DOFIMU11_CNTL2_MAG_EN_STANDBY_MODE

#define C6DOFIMU11_CNTL2_MAG_EN_STANDBY_MODE 0x00

◆ C6DOFIMU11_CNTL2_RES_MAX2

#define C6DOFIMU11_CNTL2_RES_MAX2 0x0C

◆ C6DOFIMU11_CNTL2_TEMP_EN_STANDBY_MODE

#define C6DOFIMU11_CNTL2_TEMP_EN_STANDBY_MODE 0x00

6DOF IMU 11 bit mask.

Bit mask of 6DOF IMU 11 click driver.

◆ C6DOFIMU11_I2C_SLAVE_ADDRESS_GND

#define C6DOFIMU11_I2C_SLAVE_ADDRESS_GND 0x0E

6DOF IMU 11 device address setting.

Specified setting for device slave address selection of 6DOF IMU 11 click driver.

◆ C6DOFIMU11_I2C_SLAVE_ADDRESS_VCC

#define C6DOFIMU11_I2C_SLAVE_ADDRESS_VCC 0x0F

◆ C6DOFIMU11_INC3_IEL1_FIFO_TRIG

#define C6DOFIMU11_INC3_IEL1_FIFO_TRIG 0x02

◆ C6DOFIMU11_INC3_IEL2_FIFO_TRIG

#define C6DOFIMU11_INC3_IEL2_FIFO_TRIG 0x20

◆ C6DOFIMU11_WHO_AM_I_WIA_ID

#define C6DOFIMU11_WHO_AM_I_WIA_ID 0x2D

◆ I2CEXTEND_ALERT_EN_FAULT

#define I2CEXTEND_ALERT_EN_FAULT 0x04

◆ I2CEXTEND_ALERT_EN_FAULT_DISABLE

#define I2CEXTEND_ALERT_EN_FAULT_DISABLE 0x00

◆ I2CEXTEND_ALERT_EN_LINK_GOOD

#define I2CEXTEND_ALERT_EN_LINK_GOOD 0x01

◆ I2CEXTEND_ALERT_EN_LINK_GOOD_DISABLE

#define I2CEXTEND_ALERT_EN_LINK_GOOD_DISABLE 0x00

I2C Extend alert enable.

Alert enable settings of I2C Extend Click driver.

◆ I2CEXTEND_ALERT_EN_LINK_LOST

#define I2CEXTEND_ALERT_EN_LINK_LOST 0x02

◆ I2CEXTEND_ALERT_EN_LINK_LOST_DISABLE

#define I2CEXTEND_ALERT_EN_LINK_LOST_DISABLE 0x00

◆ I2CEXTEND_CONFIG_CTRL_SEL_BIT_MASK

#define I2CEXTEND_CONFIG_CTRL_SEL_BIT_MASK 0x02

◆ I2CEXTEND_CONFIG_CTRL_SEL_MIRRORED_RMT_OUT

#define I2CEXTEND_CONFIG_CTRL_SEL_MIRRORED_RMT_OUT 0x00

◆ I2CEXTEND_CONFIG_CTRL_SEL_USE_REG_CTRL_VAL

#define I2CEXTEND_CONFIG_CTRL_SEL_USE_REG_CTRL_VAL 0x02

◆ I2CEXTEND_CONFIG_INTR_MODE_BIT_MASK

#define I2CEXTEND_CONFIG_INTR_MODE_BIT_MASK 0x01

I2C Extend description setting.

Specified setting for description of I2C Extend Click driver.

◆ I2CEXTEND_CONFIG_INTR_MODE_IGNORE_ARA

#define I2CEXTEND_CONFIG_INTR_MODE_IGNORE_ARA 0x01

◆ I2CEXTEND_CONFIG_INTR_MODE_SET_ALERT_PIN

#define I2CEXTEND_CONFIG_INTR_MODE_SET_ALERT_PIN 0x00

◆ I2CEXTEND_CTRL_SEL_H

#define I2CEXTEND_CTRL_SEL_H 0x01

◆ I2CEXTEND_CTRL_SEL_L

#define I2CEXTEND_CTRL_SEL_L 0x00

I2C Extend control.

Control settings of I2C Extend Click driver.

◆ I2CEXTEND_I2C_SLAVE_ADDR_0

#define I2CEXTEND_I2C_SLAVE_ADDR_0 0x3E

I2C Extend device address setting.

Specified setting for device slave address selection of I2C Extend Click driver.

◆ I2CEXTEND_I2C_SLAVE_ADDR_1

#define I2CEXTEND_I2C_SLAVE_ADDR_1 0x3F

◆ I2CEXTEND_I2C_SLAVE_ADDR_2

#define I2CEXTEND_I2C_SLAVE_ADDR_2 0x76

◆ I2CEXTEND_I2C_SLAVE_ADDR_3

#define I2CEXTEND_I2C_SLAVE_ADDR_3 0x77

◆ I2CEXTEND_PIN_STATE_HIGH

#define I2CEXTEND_PIN_STATE_HIGH 0x01

◆ I2CEXTEND_PIN_STATE_LOW

#define I2CEXTEND_PIN_STATE_LOW 0x00

I2C Extend pin state.

Pin state of I2C Extend Click driver.

Macros