Settings for registers of N-PLC Click driver. More...

Macros
#define	NPLC_CMD_COMMAND_MODE "+++"
	N-PLC control commands.

#define	NPLC_CMD_DATA_MODE "ATO"

#define	NPLC_CMD_S100 "ATS100"

#define	NPLC_CMD_S110 "ATS110"

#define	NPLC_CMD_S111 "ATS111"

#define	NPLC_CMD_S112 "ATS112"

#define	NPLC_CMD_S113 "ATS113"

#define	NPLC_CMD_S114 "ATS114"

#define	NPLC_CMD_S300 "ATS300"

#define	NPLC_CMD_S301 "ATS301"

#define	NPLC_CMD_S302 "ATS302"

#define	NPLC_CMD_S305 "ATS305"

#define	NPLC_CMD_S306 "ATS306"

#define	NPLC_CMD_FWI "AT+FWI"

#define	NPLC_CMD_X "ATX"

#define	NPLC_CMD_Z "ATZ"

#define	NPLC_CMD_F "AT&F"

#define	NPLC_CMD_W "AT&W"

#define	NPLC_CMD_H "AT&H"

#define	NPLC_CMD_V "AT&V"

#define	NPLC_MODE_COMMAND 0
	N-PLC mode selection.

#define	NPLC_MODE_DATA 1

#define	NPLC_DRV_BUFFER_SIZE 200
	N-PLC driver buffer size.

Detailed Description

Settings for registers of N-PLC Click driver.

Macro Definition Documentation

◆ NPLC_CMD_COMMAND_MODE

#define NPLC_CMD_COMMAND_MODE "+++"

N-PLC control commands.

Specified setting for control commands of N-PLC Click driver. Go to command mode.

◆ NPLC_CMD_DATA_MODE

#define NPLC_CMD_DATA_MODE "ATO"

Go online - data mode.

◆ NPLC_CMD_F

#define NPLC_CMD_F "AT&F"

Load factory default configuration.

◆ NPLC_CMD_FWI

#define NPLC_CMD_FWI "AT+FWI"

Show firmware version.

◆ NPLC_CMD_H

#define NPLC_CMD_H "AT&H"

Show help (this).

◆ NPLC_CMD_S100

#define NPLC_CMD_S100 "ATS100"

G3/IEEE modulation code.

◆ NPLC_CMD_S110

#define NPLC_CMD_S110 "ATS110"

XXR sub-carriers.

◆ NPLC_CMD_S111

#define NPLC_CMD_S111 "ATS111"

XXR band, 0=CENELEC, 1=FCC.

◆ NPLC_CMD_S112

#define NPLC_CMD_S112 "ATS112"

XXR redundancy.

◆ NPLC_CMD_S113

#define NPLC_CMD_S113 "ATS113"

G3/IEEE operation mode.

◆ NPLC_CMD_S114

#define NPLC_CMD_S114 "ATS114"

Transmit level attenuation in dB.

◆ NPLC_CMD_S300

#define NPLC_CMD_S300 "ATS300"

ASCII passthru default enabled.

◆ NPLC_CMD_S301

#define NPLC_CMD_S301 "ATS301"

Default run mode, 0=command, 1=data.

◆ NPLC_CMD_S302

#define NPLC_CMD_S302 "ATS302"

Packet terminator, 1=CR, 2=LF, 3=CRLF, 4=EOT.

◆ NPLC_CMD_S305

#define NPLC_CMD_S305 "ATS305"

Packet timeout in ms.

◆ NPLC_CMD_S306

#define NPLC_CMD_S306 "ATS306"

Hardware handshake enable (1).

◆ NPLC_CMD_V

#define NPLC_CMD_V "AT&V"

Show current configuration.

◆ NPLC_CMD_W

#define NPLC_CMD_W "AT&W"

Write configuration to flash.

◆ NPLC_CMD_X

#define NPLC_CMD_X "ATX"

Exit ASCII mode.

◆ NPLC_CMD_Z

#define NPLC_CMD_Z "ATZ"

Do reset.

◆ NPLC_DRV_BUFFER_SIZE

#define NPLC_DRV_BUFFER_SIZE 200

N-PLC driver buffer size.

Specified size of driver ring buffer.

Note: Increase buffer size if needed.

◆ NPLC_MODE_COMMAND

#define NPLC_MODE_COMMAND 0

N-PLC mode selection.

Specified mode selection of N-PLC Click driver.

◆ NPLC_MODE_DATA

#define NPLC_MODE_DATA 1

Macros