pressure16 2.0.0.0
Pressure 16 Registers Settings

Settings for registers of Pressure 16 Click driver. More...

Macros

#define PRESSURE16_SET_CTRL_ODR_POWER_DOWN_MODE   0x00
 Pressure 16 description setting.
 
#define PRESSURE16_SET_CTRL_ODR_1   0x01
 
#define PRESSURE16_SET_CTRL_ODR_10   0x02
 
#define PRESSURE16_SET_CTRL_ODR_25   0x03
 
#define PRESSURE16_SET_CTRL_ODR_50   0x04
 
#define PRESSURE16_SET_CTRL_ODR_75   0x05
 
#define PRESSURE16_SET_CTRL_ODR_100   0x06
 
#define PRESSURE16_SET_CTRL_ODR_200   0x07
 
#define PRESSURE16_SET_CTRL_LPFP_DISABLE   0x00
 
#define PRESSURE16_SET_CTRL_LPFP_DISABLE   0x00
 
#define PRESSURE16_SET_CTRL_LPFP_ENABLE   0x01
 
#define PRESSURE16_SET_CTRL_LPFP_ENABLE   0x01
 
#define PRESSURE16_SET_BDU_DATA_UPDATES_CONTINUOUS   0x00
 
#define PRESSURE16_SET_BDU_DATA_NOT_UPDATES_UNTIL_READ   0x01
 
#define PRESSURE16_SET_SIM_SPI_4_WIRE_INTERFACE   0x00
 
#define PRESSURE16_SET_SIM_SPI_3_WIRE_INTERFACE   0x01
 
#define PRESSURE16_SET_BOOT_NORMAL_OPERATION   0x00
 
#define PRESSURE16_SET_BOOT_REBOOT_MEMORY_CONTENT   0x01
 
#define PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_HIGH   0x00
 
#define PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_LOW   0x01
 
#define PRESSURE16_SET_PP_OD_PUSH_PULL   0x00
 
#define PRESSURE16_SET_PP_OD_OPEN_DRAIN   0x01
 
#define PRESSURE16_SET_IF_ADD_INC_DISABLED   0x00
 
#define PRESSURE16_SET_IF_ADD_INC_ENABLED   0x01
 
#define PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_POWER_MODE   0x00
 
#define PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_NOISE_MODE   0x01
 
#define PRESSURE16_SET_ONE_SHOT_NORMAL_OPERATION   0x00
 
#define PRESSURE16_SET_ONE_SHOT_NEW_DATA_SET_IS_ACQUIRED   0x01
 
#define PRESSURE16_SET_INT_F_FULL_DISABLED   0x00
 
#define PRESSURE16_SET_INT_F_FULL_ENABLED   0x01
 
#define PRESSURE16_SET_INT_F_WTM_DISABLED   0x00
 
#define PRESSURE16_SET_INT_F_WTM_ENABLED   0x01
 
#define PRESSURE16_SET_INT_F_OVR_DISABLED   0x00
 
#define PRESSURE16_SET_INT_F_OVR_ENABLED   0x01
 
#define PRESSURE16_SET_DRDY_DISABLED   0x00
 
#define PRESSURE16_SET_DRDY_ENABLED   0x01
 
#define PRESSURE16_SET_INT_S_DATA_SIGNAL   0x00
 
#define PRESSURE16_SET_INT_S_PRESSURE_HIGH_EVENT   0x01
 
#define PRESSURE16_SET_INT_S_PRESSURE_LOW_EVENT   0x02
 
#define PRESSURE16_SET_INT_S_PRESSURE_LOW_HIGH_EVENT   0x03
 
#define PRESSURE16_SET_INT_CFG_AUTOREFP_DISABLED   0x00
 
#define PRESSURE16_SET_INT_CFG_AUTOREFP_ENABLED   0x01
 
#define PRESSURE16_SET_INT_CFG_RESET_ARP_NORMAL_MODE   0x00
 
#define PRESSURE16_SET_INT_CFG_RESET_ARP_RST_AUTOREFP   0x01
 
#define PRESSURE16_SET_INT_CFG_AUTOZERO_DISABLED   0x00
 
#define PRESSURE16_SET_INT_CFG_AUTOZERO_ENABLED   0x01
 
#define PRESSURE16_SET_INT_CFG_AUTOZERO_NORMAL_MODE   0x00
 
#define PRESSURE16_SET_INT_CFG_RST_AUTOZERO   0x01
 
#define PRESSURE16_SET_INT_CFG_DIFF_EN_DISABLED   0x00
 
#define PRESSURE16_SET_INT_CFG_DIFF_EN_ENABLED   0x01
 
#define PRESSURE16_SET_INT_CFG_LIR_INT_IS_NOT_LATCHED   0x00
 
#define PRESSURE16_SET_INT_CFG_LIR_INT_IS_LATCHED   0x01
 
#define PRESSURE16_SET_INT_CFG_PLE_INT_IS_INACTIVE   0x00
 
#define PRESSURE16_SET_INT_CFG_PLE_INT_IS_ACTIVE   0x01
 
#define PRESSURE16_SET_INT_CFG_PHE_INT_IS_INACTIVE   0x00
 
#define PRESSURE16_SET_INT_CFG_PHE_INT_IS_ACTIVE   0x01
 
#define PRESSURE16_SET_SW_RESET_BIT_MASK   0x04
 
#define PRESSURE16_SET_DEV_ADDR_GND   0x5C
 Pressure 16 device address setting.
 
#define PRESSURE16_SET_DEV_ADDR_VCC   0x5D
 
#define PRESSURE16_DEVICE_ID   0xB3
 Pressure 16 device ID value.
 

Detailed Description

Settings for registers of Pressure 16 Click driver.

Macro Definition Documentation

◆ PRESSURE16_DEVICE_ID

#define PRESSURE16_DEVICE_ID   0xB3

Pressure 16 device ID value.

Specified setting for device device ID value of Pressure 16 Click driver.

◆ PRESSURE16_SET_BDU_DATA_NOT_UPDATES_UNTIL_READ

#define PRESSURE16_SET_BDU_DATA_NOT_UPDATES_UNTIL_READ   0x01

◆ PRESSURE16_SET_BDU_DATA_UPDATES_CONTINUOUS

#define PRESSURE16_SET_BDU_DATA_UPDATES_CONTINUOUS   0x00

◆ PRESSURE16_SET_BOOT_NORMAL_OPERATION

#define PRESSURE16_SET_BOOT_NORMAL_OPERATION   0x00

◆ PRESSURE16_SET_BOOT_REBOOT_MEMORY_CONTENT

#define PRESSURE16_SET_BOOT_REBOOT_MEMORY_CONTENT   0x01

◆ PRESSURE16_SET_CTRL_LPFP_DISABLE [1/2]

#define PRESSURE16_SET_CTRL_LPFP_DISABLE   0x00

◆ PRESSURE16_SET_CTRL_LPFP_DISABLE [2/2]

#define PRESSURE16_SET_CTRL_LPFP_DISABLE   0x00

◆ PRESSURE16_SET_CTRL_LPFP_ENABLE [1/2]

#define PRESSURE16_SET_CTRL_LPFP_ENABLE   0x01

◆ PRESSURE16_SET_CTRL_LPFP_ENABLE [2/2]

#define PRESSURE16_SET_CTRL_LPFP_ENABLE   0x01

◆ PRESSURE16_SET_CTRL_ODR_1

#define PRESSURE16_SET_CTRL_ODR_1   0x01

◆ PRESSURE16_SET_CTRL_ODR_10

#define PRESSURE16_SET_CTRL_ODR_10   0x02

◆ PRESSURE16_SET_CTRL_ODR_100

#define PRESSURE16_SET_CTRL_ODR_100   0x06

◆ PRESSURE16_SET_CTRL_ODR_200

#define PRESSURE16_SET_CTRL_ODR_200   0x07

◆ PRESSURE16_SET_CTRL_ODR_25

#define PRESSURE16_SET_CTRL_ODR_25   0x03

◆ PRESSURE16_SET_CTRL_ODR_50

#define PRESSURE16_SET_CTRL_ODR_50   0x04

◆ PRESSURE16_SET_CTRL_ODR_75

#define PRESSURE16_SET_CTRL_ODR_75   0x05

◆ PRESSURE16_SET_CTRL_ODR_POWER_DOWN_MODE

#define PRESSURE16_SET_CTRL_ODR_POWER_DOWN_MODE   0x00

Pressure 16 description setting.

Specified setting for description of Pressure 16 Click driver.

◆ PRESSURE16_SET_DEV_ADDR_GND

#define PRESSURE16_SET_DEV_ADDR_GND   0x5C

Pressure 16 device address setting.

Specified setting for device slave address selection of Pressure 16 Click driver.

◆ PRESSURE16_SET_DEV_ADDR_VCC

#define PRESSURE16_SET_DEV_ADDR_VCC   0x5D

◆ PRESSURE16_SET_DRDY_DISABLED

#define PRESSURE16_SET_DRDY_DISABLED   0x00

◆ PRESSURE16_SET_DRDY_ENABLED

#define PRESSURE16_SET_DRDY_ENABLED   0x01

◆ PRESSURE16_SET_IF_ADD_INC_DISABLED

#define PRESSURE16_SET_IF_ADD_INC_DISABLED   0x00

◆ PRESSURE16_SET_IF_ADD_INC_ENABLED

#define PRESSURE16_SET_IF_ADD_INC_ENABLED   0x01

◆ PRESSURE16_SET_INT_CFG_AUTOREFP_DISABLED

#define PRESSURE16_SET_INT_CFG_AUTOREFP_DISABLED   0x00

◆ PRESSURE16_SET_INT_CFG_AUTOREFP_ENABLED

#define PRESSURE16_SET_INT_CFG_AUTOREFP_ENABLED   0x01

◆ PRESSURE16_SET_INT_CFG_AUTOZERO_DISABLED

#define PRESSURE16_SET_INT_CFG_AUTOZERO_DISABLED   0x00

◆ PRESSURE16_SET_INT_CFG_AUTOZERO_ENABLED

#define PRESSURE16_SET_INT_CFG_AUTOZERO_ENABLED   0x01

◆ PRESSURE16_SET_INT_CFG_AUTOZERO_NORMAL_MODE

#define PRESSURE16_SET_INT_CFG_AUTOZERO_NORMAL_MODE   0x00

◆ PRESSURE16_SET_INT_CFG_DIFF_EN_DISABLED

#define PRESSURE16_SET_INT_CFG_DIFF_EN_DISABLED   0x00

◆ PRESSURE16_SET_INT_CFG_DIFF_EN_ENABLED

#define PRESSURE16_SET_INT_CFG_DIFF_EN_ENABLED   0x01

◆ PRESSURE16_SET_INT_CFG_LIR_INT_IS_LATCHED

#define PRESSURE16_SET_INT_CFG_LIR_INT_IS_LATCHED   0x01

◆ PRESSURE16_SET_INT_CFG_LIR_INT_IS_NOT_LATCHED

#define PRESSURE16_SET_INT_CFG_LIR_INT_IS_NOT_LATCHED   0x00

◆ PRESSURE16_SET_INT_CFG_PHE_INT_IS_ACTIVE

#define PRESSURE16_SET_INT_CFG_PHE_INT_IS_ACTIVE   0x01

◆ PRESSURE16_SET_INT_CFG_PHE_INT_IS_INACTIVE

#define PRESSURE16_SET_INT_CFG_PHE_INT_IS_INACTIVE   0x00

◆ PRESSURE16_SET_INT_CFG_PLE_INT_IS_ACTIVE

#define PRESSURE16_SET_INT_CFG_PLE_INT_IS_ACTIVE   0x01

◆ PRESSURE16_SET_INT_CFG_PLE_INT_IS_INACTIVE

#define PRESSURE16_SET_INT_CFG_PLE_INT_IS_INACTIVE   0x00

◆ PRESSURE16_SET_INT_CFG_RESET_ARP_NORMAL_MODE

#define PRESSURE16_SET_INT_CFG_RESET_ARP_NORMAL_MODE   0x00

◆ PRESSURE16_SET_INT_CFG_RESET_ARP_RST_AUTOREFP

#define PRESSURE16_SET_INT_CFG_RESET_ARP_RST_AUTOREFP   0x01

◆ PRESSURE16_SET_INT_CFG_RST_AUTOZERO

#define PRESSURE16_SET_INT_CFG_RST_AUTOZERO   0x01

◆ PRESSURE16_SET_INT_F_FULL_DISABLED

#define PRESSURE16_SET_INT_F_FULL_DISABLED   0x00

◆ PRESSURE16_SET_INT_F_FULL_ENABLED

#define PRESSURE16_SET_INT_F_FULL_ENABLED   0x01

◆ PRESSURE16_SET_INT_F_OVR_DISABLED

#define PRESSURE16_SET_INT_F_OVR_DISABLED   0x00

◆ PRESSURE16_SET_INT_F_OVR_ENABLED

#define PRESSURE16_SET_INT_F_OVR_ENABLED   0x01

◆ PRESSURE16_SET_INT_F_WTM_DISABLED

#define PRESSURE16_SET_INT_F_WTM_DISABLED   0x00

◆ PRESSURE16_SET_INT_F_WTM_ENABLED

#define PRESSURE16_SET_INT_F_WTM_ENABLED   0x01

◆ PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_HIGH

#define PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_HIGH   0x00

◆ PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_LOW

#define PRESSURE16_SET_INT_H_L_INTERRUPT_ACTIVE_LOW   0x01

◆ PRESSURE16_SET_INT_S_DATA_SIGNAL

#define PRESSURE16_SET_INT_S_DATA_SIGNAL   0x00

◆ PRESSURE16_SET_INT_S_PRESSURE_HIGH_EVENT

#define PRESSURE16_SET_INT_S_PRESSURE_HIGH_EVENT   0x01

◆ PRESSURE16_SET_INT_S_PRESSURE_LOW_EVENT

#define PRESSURE16_SET_INT_S_PRESSURE_LOW_EVENT   0x02

◆ PRESSURE16_SET_INT_S_PRESSURE_LOW_HIGH_EVENT

#define PRESSURE16_SET_INT_S_PRESSURE_LOW_HIGH_EVENT   0x03

◆ PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_NOISE_MODE

#define PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_NOISE_MODE   0x01

◆ PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_POWER_MODE

#define PRESSURE16_SET_LOW_NOISE_ENABLE_LOW_POWER_MODE   0x00

◆ PRESSURE16_SET_ONE_SHOT_NEW_DATA_SET_IS_ACQUIRED

#define PRESSURE16_SET_ONE_SHOT_NEW_DATA_SET_IS_ACQUIRED   0x01

◆ PRESSURE16_SET_ONE_SHOT_NORMAL_OPERATION

#define PRESSURE16_SET_ONE_SHOT_NORMAL_OPERATION   0x00

◆ PRESSURE16_SET_PP_OD_OPEN_DRAIN

#define PRESSURE16_SET_PP_OD_OPEN_DRAIN   0x01

◆ PRESSURE16_SET_PP_OD_PUSH_PULL

#define PRESSURE16_SET_PP_OD_PUSH_PULL   0x00

◆ PRESSURE16_SET_SIM_SPI_3_WIRE_INTERFACE

#define PRESSURE16_SET_SIM_SPI_3_WIRE_INTERFACE   0x01

◆ PRESSURE16_SET_SIM_SPI_4_WIRE_INTERFACE

#define PRESSURE16_SET_SIM_SPI_4_WIRE_INTERFACE   0x00

◆ PRESSURE16_SET_SW_RESET_BIT_MASK

#define PRESSURE16_SET_SW_RESET_BIT_MASK   0x04