Main Page

---

Boost 4 click

Boost 4 click carries the TPS61230A, a high efficiency fully integrated synchronous boost converter from Texas Instruments. The click is designed to run on a 3.3V power supply.

click Product page

---

Click library

• Author : Jovan Stajkovic
• Date : Dec 2019.
• Type : SPI type

Software Support

We provide a library for the Boost4 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

‍This library contains API for Boost4 Click driver.

Standard key functions :

• Config Object Initialization function.

  ‍void boost4_cfg_setup ( boost4_cfg_t *cfg );

  - Initialization function.

  ‍BOOST4_RETVAL boost4_init ( boost4_t *ctx, boost4_cfg_t *cfg );

Example key functions :

• Generic SPI transfer, for sending and receiving packages.

  ‍void boost4_generic_transfer ( boost4_t *ctx, spi_master_transfer_data_t *block );

  - Function set output voltage by write 12-bit data to the register on the TPS61230A High Efficiency Step-Up Converter of Boost 4 Click.

  ‍void boost4_set_out_voltage ( boost4_t *ctx, uint16_t value );

• Function is used to enabled or disabled the device.

  ‍void boost4_enable ( boost4_t *ctx, uint8_t state );

  Examples Description

‍This example demonstrates the use of Boost 4 Click board.

The demo application is composed of two sections :

Application Init

‍Initializes the driver and logger, and enables the click board.

void application_init ( void )
{
    log_cfg_t log_cfg;
    boost4_cfg_t cfg;
 
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );
 
    //  Click initialization.
 
    boost4_cfg_setup( &cfg );
    BOOST4_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    boost4_init( &boost4, &cfg );
    log_printf( &logger, "-----------------------------\r\n" );
    log_printf( &logger, "        Boost 4 Click        \r\n" );
    log_printf( &logger, "-----------------------------\r\n" );
    boost4_enable( &boost4, BOOST4_ENABLE );
    Delay_ms ( 1000 );
}

Application Task

‍Set the desired output voltage by cycling through a couple of predefined voltage values. All data are being logged on USB UART every 3 seconds.

void application_task ( void )
{
    log_printf( &logger, " Set the max Vout \r\n" );
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_MAX );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
 
    log_printf( &logger, " Set Vout to 5V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_5 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    
    log_printf( &logger, "-----------------------------\r\n" );
 
    log_printf( &logger, " Set Vout to 4.5V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_4_5 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
    
    log_printf( &logger, " Set Vout to 4V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_4 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
    
    log_printf( &logger, " Set Vout to 3.5V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_3_5 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
    
    log_printf( &logger, " Set Vout to 3V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_3 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
    
    log_printf( &logger, " Set Vout to 2.5V\r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_2_5 );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
    
    log_printf( &logger, " Set the min Vout \r\n" );
 
    boost4_set_out_voltage( &boost4, BOOST4_VOUT_MIN );
 
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf( &logger, "-----------------------------\r\n" );
}  

Note

‍Vout cannot be set to voltage below Vin. So in order to get all values at Vout exactly as it is set in this example, please provide 2.5V to Vin.

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Boost4

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---