Main Page

---

Expand 4 click

Expand 4 click carries TPCIC6A595, a chip that combines an 8-bit serial-in, parallel-out shift register with an 8-bit D-type storage register.

click Product page

---

Click library

• Author : MikroE Team
• Date : Dec 2019.
• Type : SPI type

Software Support

We provide a library for the Expand4 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

‍This library contains API for Expand4 Click driver.

Standard key functions :

• Config Object Initialization function.

  ‍void expand4_cfg_setup ( expand4_cfg_t *cfg );

  - Initialization function.

  ‍EXPAND4_RETVAL expand4_init ( expand4_t *ctx, expand4_cfg_t *cfg );

• Click Default Configuration function.

  ‍void expand4_default_cfg ( expand4_t *ctx );

Example key functions :

• Function write 8-bit data function to TPIC6A595 shift register.

  ‍void expand4_write_data( expand4_t *ctx, uint8_t write_command );

  - Function turn on output buffers - set PWM pin low

  ‍void expand4_enable_output( expand4_t *ctx );

• Function clear input TPIC6A595 shift register.

  ‍void expand4_reset( expand4_t *ctx );

  Examples Description

‍Example demonstrates use of Expand 4 Click board.

The demo application is composed of two sections :

Application Init

‍Initialization driver enable's - Clear TPIC6A595 register and start write log.

void application_init ( void )
{
    log_cfg_t log_cfg;
    expand4_cfg_t cfg;
 
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );
 
    //  Click initialization.
 
    expand4_cfg_setup( &cfg );
    EXPAND4_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    expand4_init( &expand4, &cfg );
    expand4_reset( &expand4 );
}

Application Task

‍This is a example which demonstrates the use of Expand 4 Click board. In this example, the LED pin mask is transferred via SPI bus, LEDs connected to D0-D7 pins are lit accordingly by turning ON LEDs from D0 to D7 for 3 sec. Results are being sent to the Usart Terminal where you can track their changes. All data logs on usb uart for aproximetly every 3 sec. when the change pin who is connected.

void application_task ( void )
{
    uint8_t pin_position;
 
    for ( pin_position = 0; pin_position < 8; pin_position++ )
    {
        expand4_disable_output( &expand4 );
        Delay_ms ( 100 );
 
        expand4_turn_on_by_position( &expand4, pin_position );
        Delay_ms ( 100 );
 
        log_printf( &logger, " D%d", pin_position );
 
        expand4_enable_output( &expand4 );
        Delay_ms ( 1000 );
        Delay_ms ( 1000 );
        Delay_ms ( 1000 );
    }
 
    log_printf( &logger, "\n----------------------------------\n");
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Expand4

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---