Main Page

---

Pwm Driver click

If you need to control DC motors with loads up to 10A, PWM driver click is the perfect solution, thanks to the Silicon Lab Si8711CC one-channel isolator.

click Product page

---

Click library

• Author : Nikola Peric
• Date : Feb 2022.
• Type : PWM type

Software Support

We provide a library for the PwmDriver Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

‍This library contains API for PwmDriver Click driver.

Standard key functions :

• Config Object Initialization function.

  ‍void pwmdriver_cfg_setup ( pwmdriver_cfg_t *cfg );

  - Initialization function.

  ‍PWMDRIVER_RETVAL pwmdriver_init ( pwmdriver_t *ctx, pwmdriver_cfg_t *cfg );

• Click Default Configuration function.

  ‍void pwmdriver_default_cfg ( pwmdriver_t *ctx );

Example key functions :

• Generic sets PWM duty cycle

  ‍void pwmdriver_set_duty_cycle ( pwmdriver_t *ctx, pwm_data_t duty_cycle );

  - Stop PWM module.

  ‍void pwmdriver_pwm_stop ( pwmdriver_t *ctx );

• Start PWM module

  ‍void pwmdriver_pwm_start ( pwmdriver_t *ctx );

  Examples Description

‍This application is controls the speed DC motors.

The demo application is composed of two sections :

Application Init

>Initialization driver enables - GPIO, PWM initialization set PWM duty cycle and PWM frequency, start PWM, enable the engine, and start to write log.

void application_init ( void )
{
    log_cfg_t log_cfg;
    pwmdriver_cfg_t cfg;
 
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );
 
    //  Click initialization.
 
    pwmdriver_cfg_setup( &cfg );
    PWMDRIVER_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    pwmdriver_init( &pwmdriver, &cfg );
 
    Delay_ms ( 100 );
    
    log_printf( &logger, "   Initialization PWM  \r\n  " );
    pwmdriver_set_duty_cycle( &pwmdriver, 0.0 );
    pwmdriver_pwm_start( &pwmdriver );
    Delay_ms ( 1000 );
    log_info( &logger, "---- Application Task ----" );
}

Application Task

‍This is an example that demonstrates the use of the PWM driver Click board. This example shows the automatic control of PWM, the first increases duty cycle and then the duty cycle is falling. Results are being sent to the Usart Terminal where you can track their changes.

void application_task ( void )
{
    static int8_t duty_cnt = 1;
    static int8_t duty_inc = 1;
    float duty = duty_cnt / 10.0;
 
    pwmdriver_set_duty_cycle ( &pwmdriver, duty );
    log_printf( &logger, "Duty: %d%%\r\n", ( uint16_t )( duty_cnt * 10 ) );
    Delay_ms ( 500 );
    
    if ( 10 == duty_cnt ) 
    {
        duty_inc = -1;
    }
    else if ( 0 == duty_cnt ) 
    {
        duty_inc = 1;
    }
    duty_cnt += duty_inc;
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.PwmDriver

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---