Main Page

---

Temp-Log 2 click

Temp-Log 2 click is a precise ambient temperature measurement device, equipped with the additional non-volatile (EEPROM) memory that can be used to permanently store system configuration, and 64 bits of general-purpose EEPROM, used for logging application specific or user preference data. This click covers a range of temperatures from -55°C to +125°C with the highest accuracy of ±0.2°C

click Product page

---

Click library

• Author : Nemanja Medakovic
• Date : Nov 2019.
• Type : I2C type

Software Support

We provide a library for the TempLog2 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

‍This library contains API for TempLog2 Click driver.

Standard key functions :

• Configuration Object Setup function.

  ‍void templog2_cfg_setup( templog2_cfg_t *cfg );

  - Click Initialization function.

  ‍TEMPLOG2_RETVAL templog2_init( templog2_t *ctx, templog2_cfg_t *cfg );

• Click Default Configuration function.

  ‍void templog2_default_cfg( templog2_t *ctx );

Example key functions :

• Write Register function.

  ‍TEMPLOG2_RETVAL templog2_write_reg( templog2_t *ctx, uint8_t reg_addr, uint16_t transfer_data );

  - Read Register function.

  ‍TEMPLOG2_RETVAL templog2_read_reg( templog2_t *ctx, uint8_t reg_addr, uint16_t *data_out );

• Read Temperature function.

  ‍float templog2_read_temp( templog2_t *ctx );

  Examples Description

‍ This example demonstrates the use of the Temp-Log 2 Click board.

The demo application is composed of two sections :

Application Init

‍ Initializes peripherals and pins. Initializes I2C driver and performs device configuration. Sets total active conversion time to 250 ms and 8 average samples. Also sets Shutdown Mode as default mode, and after device reset puts device in Continuous Conversion Mode. High limit status will be set when temperature cross over the determined high limit temperature value. Low limit status will be set when temperature falls below the determined low limit temperature value.

void application_init( void )
{
    templog2_cfg_t templog2_cfg;
    log_cfg_t log_cfg;
 
    //  Click initialization.
    templog2_cfg_setup( &templog2_cfg );
    TEMPLOG2_MAP_MIKROBUS( templog2_cfg, MIKROBUS_1 );
    templog2_init( &templog2, &templog2_cfg );
 
    //  Click default configuration.
    templog2_default_config( &templog2 );
 
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "----  Temp-Log 2 Application Init Done  ----\r\n" );
}

Application Task

‍ Reads temperature value calculated to Celsius degrees.

void application_task( void )
{
    float temperature;
    uint8_t temp_status;
    uint8_t cnt;
 
    temp_status = templog2_data_ready( &templog2 );
 
    if (temp_status & _TEMPLOG2_DATA_READY_MASK)
    {
        temperature = templog2_read_temp( &templog2 );
 
        log_printf( &logger, " > Temperature : %.2f\r\n", temperature );
 
        if (temp_status & _TEMPLOG2_LOW_LIMIT_MASK)
        {
            log_printf( &logger, " LOW LIMIT DETECTED!\r\n" );
        }
 
        if (temp_status & _TEMPLOG2_HIGH_LIMIT_MASK)
        {
            log_printf( &logger, " HIGH LIMIT DETECTED!\r\n" );
        }
    }
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.TempLog2

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---