Main Page

---

Stepper 6 click

‍Stepper 6 click is the complete integrated bipolar step motor driver solution. It comes with the abundance of features that allow silent operation and optimal working conditions for the connected motor. A specialized integrated driver chip on this Click board™ far exceeds the capabilities of similar, commonly used step motor drivers. It comes in the package which also includes the mikroSDK™ software, and a library with all the functions.

click Product page

---

Click library

• Author : Stefan Filipovic
• Date : Feb 2024.
• Type : I2C/SPI type

Software Support

We provide a library for the Stepper 6 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

‍This library contains API for Stepper 6 Click driver.

Standard key functions :

• stepper6_cfg_setup Config Object Initialization function.

  void stepper6_cfg_setup ( stepper6_cfg_t *cfg );

• stepper6_init Initialization function.

  err_t stepper6_init ( stepper6_t *ctx, stepper6_cfg_t *cfg );

• stepper6_default_cfg Click Default Configuration function.

  err_t stepper6_default_cfg ( stepper6_t *ctx );

Example key functions :

• stepper6_set_direction This function sets the motor direction by setting the DIR pin logic state.

  void stepper6_set_direction ( stepper6_t *ctx, uint8_t dir );

• stepper6_set_step_mode This function sets the step mode resolution settings.

  err_t stepper6_set_step_mode ( stepper6_t *ctx, uint8_t mode );

• stepper6_drive_motor This function drives the motor for the specific number of steps at the selected speed.

  void stepper6_drive_motor ( stepper6_t *ctx, uint32_t steps, uint8_t speed );

Example Description

‍This example demonstrates the use of the Stepper 6 click board by driving the motor in both directions for a desired number of steps.

The demo application is composed of two sections :

Application Init

‍Initializes the driver and performs the click default configuration.

void application_init ( void )
{
    log_cfg_t log_cfg;  
    stepper6_cfg_t stepper6_cfg;  
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );
 
    // Click initialization.
    stepper6_cfg_setup( &stepper6_cfg );
    STEPPER6_MAP_MIKROBUS( stepper6_cfg, MIKROBUS_1 );
    err_t init_flag = stepper6_init( &stepper6, &stepper6_cfg );
    if ( ( I2C_MASTER_ERROR == init_flag ) || ( SPI_MASTER_ERROR == init_flag ) )
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }
    
    if ( STEPPER6_ERROR == stepper6_default_cfg ( &stepper6 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }
    
    log_info( &logger, " Application Task " );
}

Application Task

‍Drives the motor clockwise for 200 full steps and then counter-clockiwse for 200 half

steps and 400 quarter steps with 2 seconds delay on driving mode change. All data is being logged on the USB UART where you can track the program flow.

void application_task ( void )
{
    log_printf ( &logger, " Move 200 full steps clockwise, speed: slow\r\n\n" );
    stepper6_set_direction ( &stepper6, STEPPER6_DIR_CW );
    stepper6_set_step_mode ( &stepper6, STEPPER6_MODE_FULL_STEP );
    stepper6_drive_motor ( &stepper6, 200, STEPPER6_SPEED_SLOW );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf ( &logger, " Move 200 half steps counter-clockwise, speed: medium\r\n\n" );
    stepper6_set_direction ( &stepper6, STEPPER6_DIR_CCW );
    stepper6_set_step_mode ( &stepper6, STEPPER6_MODE_HALF_STEP );
    stepper6_drive_motor ( &stepper6, 200, STEPPER6_SPEED_MEDIUM );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
 
    log_printf ( &logger, " Move 400 quarter steps counter-clockwise, speed: fast\r\n\n" );
    stepper6_set_direction ( &stepper6, STEPPER6_DIR_CCW );
    stepper6_set_step_mode ( &stepper6, STEPPER6_MODE_QUARTER_STEP );
    stepper6_drive_motor ( &stepper6, 400, STEPPER6_SPEED_FAST );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.Stepper6

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.

---