|
|
#define | SSD1963_CMD_NOP 0X00 |
| | No operation.
|
| |
|
#define | SSD1963_CMD_SOFT_RESET 0x01 |
| | Software Reset.
|
| |
|
#define | SSD1963_CMD_GET_POWER_MODE 0x0A |
| | Get the current power mode.
|
| |
|
#define | SSD1963_CMD_GET_ADDRESS_MODE 0x0B |
| | Get the frame buffer to the display panel read order.
|
| |
|
#define | SSD1963_CMD_GET_DISPLAY_MODE 0x0D |
| | The SSD1963 returns the Display Image Mode.
|
| |
|
#define | SSD1963_CMD_GET_TEAR_EFFECT_status 0x0E |
| | Get the Tear Effect status.
|
| |
|
#define | SSD1963_CMD_ENTER_SLEEP_MODE 0x10 |
| | Turn off the panel. This command will pull high the GPIO0. If GPIO0 is configured as normal GPIO or LCD miscellaneous signal with command set_gpio_conf, this command will be ignored.
|
| |
|
#define | SSD1963_CMD_EXIT_SLEEP_MODE 0x11 |
| | Turn on the panel. This command will pull low the GPIO0. If GPIO0 is configured as normal GPIO or LCD miscellaneous signal with command set_gpio_conf, this command will be ignored.
|
| |
|
#define | SSD1963_CMD_ENTER_PARTIAL_MODE 0x12 |
| | Part of the display area is used for image display.
|
| |
|
#define | SSD1963_CMD_ENTER_NORMAL_MODE 0x13 |
| | The whole display area is used for image display.
|
| |
|
#define | SSD1963_CMD_EXIT_INVERT_MODE 0x20 |
| | Displayed image colors are not inverted.
|
| |
|
#define | SSD1963_CMD_ENTER_INVERT_MODE 0x21 |
| | Displayed image colors are inverted.
|
| |
|
#define | SSD1963_CMD_SET_GAMMA_CURVE 0x26 |
| | Selects the gamma curve used by the display panel.
|
| |
|
#define | SSD1963_CMD_SET_DISPLAY_OFF 0x28 |
| | Blanks the display panel.
|
| |
|
#define | SSD1963_CMD_SET_DISPLAY_ON 0x29 |
| | Show the image on the display panel.
|
| |
|
#define | SSD1963_CMD_SET_COLUMN_ADDRESS 0x2A |
| | Set the column address.
|
| |
|
#define | SSD1963_CMD_SET_PAGE_ADDRESS 0x2B |
| | Set the page address.
|
| |
|
#define | SSD1963_CMD_WRITE_MEMORY_START 0x2C |
| | Transfer image information from the host processor interface to the SSD1963 starting at the location provided by set_column_address and set_page_address.
|
| |
|
#define | SSD1963_CMD_READ_MEMORY_START 0x2E |
| | Transfer image data from the SSD1963 to the host processor interface starting at the location provided by set_column_address and set_page_address.
|
| |
|
#define | SSD1963_CMD_SET_PARTIAL_AREA 0x30 |
| | Defines the partial display area on the display panel.
|
| |
|
#define | SSD1963_CMD_SET_SCROLL_AREA 0x33 |
| | Defines the vertical scrolling and fixed area on display area.
|
| |
|
#define | SSD1963_CMD_SET_TEAR_OFF 0x34 |
| | Synchronization information is not sent from the SSD1963 to the host processor.
|
| |
|
#define | SSD1963_CMD_SET_TEAR_ON 0x35 |
| | Synchronization information is sent from the SSD1963 to the host processor at the start of VFP.
|
| |
|
#define | SSD1963_CMD_SET_ADDRESS_MODE 0x36 |
| | Set the read order from frame buffer to the display panel.
|
| |
|
#define | SSD1963_CMD_SET_SCROLL_START 0x37 |
| | Defines the vertical scrolling starting point.
|
| |
|
#define | SSD1963_CMD_EXIT_IDLE_MODE 0x38 |
| | Full color depth is used for the display panel.
|
| |
|
#define | SSD1963_CMD_ENTER_IDLE_MODE 0x39 |
| | Reduce color depth is used on the display panel.
|
| |
|
#define | SSD1963_CMD_WRITE_MEMORY_CONTINUE 0x3C |
| | Transfer image information from the host processor interface to the SSD1963 from the last written location.
|
| |
|
#define | SSD1963_CMD_READ_MEMORY_CONTINUE 0x3E |
| | Read image data from the SSD1963 continuing after the last read_memory_continue or read_memory_start.
|
| |
|
#define | SSD1963_CMD_SET_TEAR_SCANLINE 0x44 |
| | Synchronization information is sent from the SSD1963 to the host processor when the display panel refresh reaches the provided scan line.
|
| |
|
#define | SSD1963_CMD_GET_SCANLINE 0x45 |
| | Get the current scan line.
|
| |
|
#define | SSD1963_CMD_READ_DDB 0xA1 |
| | Read the DDB from the provided location.
|
| |
|
#define | SSD1963_CMD_SET_LCD_MODE 0xB0 |
| | Set the LCD panel mode and resolution.
|
| |
|
#define | SSD1963_CMD_GET_LCD_MODE 0xB1 |
| | Get the current LCD panel mode, pad strength and resolution.
|
| |
|
#define | SSD1963_CMD_SET_HORI_PERIOD 0xB4 |
| | Set front porch.
|
| |
|
#define | SSD1963_CMD_GET_HORI_PERIOD 0xB5 |
| | Get current front porch settings.
|
| |
|
#define | SSD1963_CMD_SET_VERT_PERIOD 0xB6 |
| | Set the vertical blanking interval between last scan line and next LFRAME pulse.
|
| |
|
#define | SSD1963_CMD_GET_VERT_PERIOD 0xB7 |
| | Get the vertical blanking interval between last scan line and next LFRAME pulse.
|
| |
|
#define | SSD1963_CMD_SET_GPIO_CONF 0xB8 |
| | Set the GPIO configuration. If the GPIO is not used for LCD, set the direction. Otherwise, they are toggled with LCD signals.
|
| |
|
#define | SSD1963_CMD_GET_GPIO_CONF 0xB9 |
| | Get the current GPIO configuration.
|
| |
|
#define | SSD1963_CMD_SET_GPIO_VALUE 0xBA |
| | Set GPIO value for GPIO configured as output.
|
| |
|
#define | SSD1963_CMD_GET_GPIO_STATUS 0xBB |
| | Read current GPIO status. If the individual GPIO was configured as input, the value is the status of the corresponding pin. Otherwise, it is the programmed value.
|
| |
|
#define | SSD1963_CMD_SET_POST_PROC 0xBC |
| | Set the image post processor.
|
| |
|
#define | SSD1963_CMD_GET_POST_PROC 0xBD |
| | Get the image post processor.
|
| |
|
#define | SSD1963_CMD_SET_PWM_CONF 0xBE |
| | Set the image post processor.
|
| |
|
#define | SSD1963_CMD_GET_PWM_CONF 0xBF |
| | Get the image post processor.
|
| |
|
#define | SSD1963_CMD_SET_LCD_GEN0 0xC0 |
| | Set the rise, fall, period and toggling properties of LCD signal generator 0.
|
| |
|
#define | SSD1963_CMD_GET_LCD_GEN0 0xC1 |
| | Get the current settings of LCD signal generator 0.
|
| |
|
#define | SSD1963_CMD_SET_LCD_GEN1 0xC2 |
| | Set the rise, fall, period and toggling properties of LCD signal generator 1.
|
| |
|
#define | SSD1963_CMD_GET_LCD_GEN1 0xC3 |
| | Get the current settings of LCD signal generator 1.
|
| |
|
#define | SSD1963_CMD_SET_LCD_GEN2 0xC4 |
| | Set the rise, fall, period and toggling properties of LCD signal generator 2.
|
| |
|
#define | SSD1963_CMD_GET_LCD_GEN2 0xC5 |
| | Get the current settings of LCD signal generator 2.
|
| |
|
#define | SSD1963_CMD_SET_LCD_GEN3 0xC6 |
| | Set the rise, fall, period and toggling properties of LCD signal generator 3.
|
| |
|
#define | SSD1963_CMD_GET_LCD_GEN3 0xC7 |
| | Get the current settings of LCD signal generator 3.
|
| |
|
#define | SSD1963_CMD_SET_GPIO0_ROP 0xC8 |
| | Set the GPIO0 with respect to the LCD signal generators using ROP operation. No effect if the GPIO0 is configured as general GPIO.
|
| |
|
#define | SSD1963_CMD_GET_GPIO0_ROP 0xC9 |
| | Get the GPIO0 properties with respect to the LCD signal generators.
|
| |
|
#define | SSD1963_CMD_SET_GPIO1_ROP 0xCA |
| | Set the GPIO1 with respect to the LCD signal generators using ROP operation. No effect if the GPIO1 is configured as general GPIO.
|
| |
|
#define | SSD1963_CMD_GET_GPIO1_ROP 0xCB |
| | Get the GPIO1 properties with respect to the LCD signal generators.
|
| |
|
#define | SSD1963_CMD_SET_GPIO2_ROP 0xCC |
| | Set the GPIO2 with respect to the LCD signal generators using ROP operation. No effect if the GPIO2 is configured as general GPIO.
|
| |
|
#define | SSD1963_CMD_GET_GPIO2_ROP 0xCD |
| | Get the GPIO2 properties with respect to the LCD signal generators.
|
| |
|
#define | SSD1963_CMD_SET_GPIO3_ROP 0xCE |
| | Set the GPIO3 with respect to the LCD signal generators using ROP operation. No effect if the GPIO3 is configured as general GPIO.
|
| |
|
#define | SSD1963_CMD_GET_GPIO3_ROP 0xCF |
| | Get the GPIO3 properties with respect to the LCD signal generators.
|
| |
|
#define | SSD1963_CMD_SET_DBC_CONF 0xD0 |
| | Set the dynamic back light configuration.
|
| |
|
#define | SSD1963_CMD_GET_DBC_CONF 0xD |
| | Get the current dynamic back light configuration.
|
| |
|
#define | SSD1963_CMD_SET_DBC_TH 0xD4 |
| | Set the threshold for each level of power saving.
|
| |
|
#define | SSD1963_CMD_GET_DBC_TH 0xD5 |
| | Get the threshold for each level of power saving.
|
| |
|
#define | SSD1963_CMD_SET_PLL 0xE0 |
| | Start the PLL. Before the start, the system was operated with the crystal oscillator or clock input.
|
| |
|
#define | SSD1963_CMD_SET_PLL_MN 0xE2 |
| | Set the PLL.
|
| |
|
#define | SSD1963_CMD_GET_PLL_MN 0xE3 |
| | Get the PLL settings.
|
| |
|
#define | SSD1963_CMD_GET_PLL_STATUS 0xE4 |
| | Get the current PLL status.
|
| |
|
#define | SSD1963_CMD_SET_DEEP_SLEEP 0xE5 |
| | Set deep sleep mode.
|
| |
|
#define | SSD1963_CMD_SET_LSHIFT_FREQ 0xE6 |
| | Set the LSHIFT (pixel clock) frequency.
|
| |
|
#define | SSD1963_CMD_GET_LSHIFT_FREQ 0xE7 |
| | Get current LSHIFT (pixel clock) frequency setting.
|
| |
|
#define | SSD1963_CMD_SET_PIXEL_DATA_INTERFACE 0xF0 |
| | Set the pixel data format of the parallel host processor interface.
|
| |
|
#define | SSD1963_CMD_GET_PIXEL_DATA_INTERFACE 0xF1 |
| | Get the current pixel data format settings.
|
| |